DBX 704X 96 KHz-24 Bit Digital Output Card For Blue Series

September 10th, 2012 by admin Leave a reply »

Dbx 560A 500 Series Compressor / Limiter


Dbx 560A 500 Series Compressor / Limiter


$199.95


The dbx 560A Compressor/Limiter offers legendary VCA-based compression in the increasingly popular 500 Series format. dbx has a much-heralded history with modular processors dating back to the 900 Series and the 560A continues that tradition.Featuring the same switch-selectable OverEasy and Hard Knee compression curves as the industry-standard dbx 160A rackmount processor, the dbx 560A will be your new workhorse compressor! With extremely wide-ranging threshold, ratio and output controls and true RMS level detection providing the most natural-sounding dynamics processing available, the 560A will provide punch to drums, bass, vocals, almost anything! Its also versatile enough to go from subtle compression to “brick wall” peak limiting.Choose low ratios and OverEasy compression to expertly smooth out fluctuating vocal and instrumental levels, or use the 560A’s Hard Knee compression and high ratios for bombproof protection against overload distortion in digital recording, P.A. systems and broadcast signals.The 560A’s 19-segment, switchable Input/Output LEDs and 12-segment Gain Reduction LEDs provide precise analysis at a glance. And, the dbx 560A’s unique “INFINITY +” inverse-compression mode actually decreases the audio output level below unity gain when the input exceeds threshold, a real lifesaver for correcting overbearing vocal choruses and controlling runaway mix levels.OverEasy or classic hard knee compression with dbx’ ultra-musical program dependent attack and release timesCompression ratio variable from 1:1 through infinity:1 to -1:1Precise RMS gain reduction and input/output meter displays with calibration control for different operating levelsTrue RMS level detectionExclusive Infinity+ compression using negative ratios

Dbx Zonepro 1261M Speaker Processor


Dbx Zonepro 1261M Speaker Processor


$749.95


The ZonePRO products have long been the obvious choice for managing commercial audio applications. They’re easy to install and use – thanks to step-by-step setup wizards – and they’re backed by long track record of dbx reliability. The fact that so many are in use in locations worldwide speaks to their popularity and dependable performance.The ZonePRO 1261m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 1261m features a total of 12 inputs and six outputs. Inputs include six balanced mic/line switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one S/PDIF input for up to two digital channels. Hardware-controlledmicrophone gain allows adjustment of microphone gain per channel.The 1261m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 1261m features a power status LED, a network traffic LED, and an RS-232 control port.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).ZonePRO Designer-the configuration, control and monito2 Inputs / 6 Outputs6 Balanced Mic/Line Inputs4 Unbalanced, Mono-Summed RCA Input PairsS/PDIF InputMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

Used Dbx Zonepro 1260M Speaker Processor


Used Dbx Zonepro 1260M Speaker Processor


$747.96


The ZonePRO 1260m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 1260m features a total of 12 inputs and six outputs. Inputs include six balanced mic/line switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one S/PDIF input for up to two digital channels. Hardware-controlled microphone gain allows adjustment of microphone gain per channel.The 1260m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanentlyavailable on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 1260m features comprehensive signal metering, an informative LCD display and user-specified front panel control.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).ZonePRO Designer-the configuration, control and monitoring software for the ZonePRO family of devices-offers control of the ZonePRO 1260m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-bystep configuration process of the 1260m.12 Inputs / 6 Outputs6 Balanced Mic/Line Inputs4 Unbalanced, Mono-Summed RCA Input PairsS/PDIF InputMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusComprehensive Signal MeteringFront Panel LCD9 User-Specified Front Panel ControlOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

dbx ZonePRO 1261m Speaker Processor


dbx ZonePRO 1261m Speaker Processor


$749.95


The ZonePRO products have long been the obvious choice for managing commercial audio applications. Theyre easy to install and use – thanks to step-by-step setup wizards – and theyre backed by long track record of dbx reliability. The fact that so many are in use in locations worldwide speaks to their popularity and dependable performance.The ZonePRO 1261m offers fixed IO, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 1261m features a total of 12 inputs and six outputs. Inputs include six balanced micline switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one SPDIF input for up to two digital channels. Hardware-controlledmicrophone gain allows adjustment of microphone gain per channel.The 1261m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 1261m features a power status LED, a network traffic LED, and an RS-232 control port.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable see table for further information.ZonePRO Designer-the configuration, control and monito2 Inputs 6 Outputs6 Balanced MicLine Inputs4 Unbalanced, Mono-Summed RCA Input PairsSPDIF InputMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

Dbx Zonepro 1260M Speaker Processor


Dbx Zonepro 1260M Speaker Processor


$849.95


The ZonePRO 1260m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 1260m features a total of 12 inputs and six outputs. Inputs include six balanced mic/line switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one S/PDIF input for up to two digital channels. Hardware-controlled microphone gain allows adjustment of microphone gain per channel.The 1260m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanentlyavailable on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 1260m features comprehensive signal metering, an informative LCD display and user-specified front panel control.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).ZonePRO Designer-the configuration, control and monitoring software for the ZonePRO family of devices-offers control of the ZonePRO 1260m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-bystep configuration process of the 1260m.12 Inputs / 6 Outputs6 Balanced Mic/Line Inputs4 Unbalanced, Mono-Summed RCA Input PairsS/PDIF InputMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusComprehensive Signal MeteringFront Panel LCD9 User-Specified Front Panel ControlOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

dbx ZonePRO 1260m Speaker Processor


dbx ZonePRO 1260m Speaker Processor


$747.96


The ZonePRO 1260m offers fixed IO, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 1260m features a total of 12 inputs and six outputs. Inputs include six balanced micline switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one SPDIF input for up to two digital channels. Hardware-controlled microphone gain allows adjustment of microphone gain per channel.The 1260m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanentlyavailable on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 1260m features comprehensive signal metering, an informative LCD display and user-specified front panel control.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable see table for further information.ZonePRO Designer-the configuration, control and monitoring software for the ZonePRO family of devices-offers control of the ZonePRO 1260m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-bystep configuration process of the 1260m.12 Inputs 6 Outputs6 Balanced MicLine Inputs4 Unbalanced, Mono-Summed RCA Input PairsSPDIF InputMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusComprehensive Signal MeteringFront Panel LCD9 User-Specified Front Panel ControlOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

dbx ZonePRO 1261m Speaker Processor  190839405210


dbx ZonePRO 1261m Speaker Processor 190839405210


$599.96


The ZonePRO products have long been the obvious choice for managing commercial audio applications. Theyre easy to install and use – thanks to step-by-step setup wizards – and theyre backed by long track record of dbx reliability. The fact that so many are in use in locations worldwide speaks to their popularity and dependable performance.The ZonePRO 1261m offers fixed IO, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 1261m features a total of 12 inputs and six outputs. Inputs include six balanced micline switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one SPDIF input for up to two digital channels. Hardware-controlledmicrophone gain allows adjustment of microphone gain per channel.The 1261m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 1261m features a power status LED, a network traffic LED, and an RS-232 control port.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable see table for further information.ZonePRO Designer-the configuration, control and monitoring software for the ZonePRO family of devices-offers control of the ZonePRO 1261m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-bystep configuration process of the 1261m.2 Inputs 6 Outputs6 Balanced MicLine Inputs4 Unbalanced, Mono-Summed RCA Input PairsSPDIF InputMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

Used Dbx Zonepro 1261M Speaker Processor  190839405210


Used Dbx Zonepro 1261M Speaker Processor 190839405210


$599.96


The ZonePRO products have long been the obvious choice for managing commercial audio applications. They’re easy to install and use – thanks to step-by-step setup wizards – and they’re backed by long track record of dbx reliability. The fact that so many are in use in locations worldwide speaks to their popularity and dependable performance.The ZonePRO 1261m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 1261m features a total of 12 inputs and six outputs. Inputs include six balanced mic/line switchable terminal block inputs, four mono-summed pairs of unbalanced RCA inputs and one S/PDIF input for up to two digital channels. Hardware-controlledmicrophone gain allows adjustment of microphone gain per channel.The 1261m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 1261m features a power status LED, a network traffic LED, and an RS-232 control port.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information).ZonePRO Designer-the configuration, control and monitoring software for the ZonePRO family of devices-offers control of the ZonePRO 1261m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-bystep configuration process of the 1261m.2 Inputs / 6 Outputs6 Balanced Mic/Line Inputs4 Unbalanced, Mono-Summed RCA Input PairsS/PDIF InputMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

dbx DriveRack PX Powered Speaker Optimizer


dbx DriveRack PX Powered Speaker Optimizer


$131.99


Powered speakers are beautiful things. Everything you need bundled into simple, tidy, portable packages. Just grab em and go, right Well, you may think your powered speaker system is complete, but youre missing half the picture. DriveRack PX is the other half. With the PX, dbx has created a processor specifically tailored for powered speakers. Utilizing dbxs highly acclaimed DriveRack technology, the PX picks up where your powered speakers leave off. The DriveRack PX Powered Speaker Optimizer has everything you need to get the most out of your stereo powered speaker system. It even includes stereo or mono subwoofer support. With the included dbx M2 measurement mic, Auto-EQ corrects for audible deficiencies in the room environment. Dbxs patented Advanced Feedback Suppression AFSTM kills nasty feedback, allowing problem-free operation at higher sound levels, while dbxs patented Subharmonic Synthesizer extends bass response for enhanced bottom end. With all that, you also get classic dbx compression and the protection offered by dbxs graceful PeakStopPlus limiting. Your ears, your audience, and your powered speakers will forever thank you. In spite of all that sophistication, rest assured dbx wont overcomplicate the simplicity of your rig. Dbxs exclusive Setup, Auto-EQ, AFS Wizards, and out-of-the-box support for a host of JBL and other popular powered speakers, make setup a snap. Louder, cleaner, better sound than you thought possible from your powered speakers.Stereo feedback elimination with 12 feedback notch filters Dual 28-band graphic EQ Classic dbx Compressor 120A subharmonic synthesizer Stereo multi-band parametric EQ Stereo PeakStopPlus limiters Pink noise generator Auto-EQ with 28-band RTA JBL and other popular powered speakers included in Setup Wizard dbx M2 measurement mic and zippered pouch included Front panel RTA-Mic XLR inputwith phantom power 25 user programs 25 factory programs 2-channel XLR Input 2-channel XLR Output 2-channel XLR Sub Output 24-bit ADC24-bit DAC, >110 dB dynamic range dbx Type IVTM conversion system Full graphic LCD display

Link Cable - 9M - Phone 2nd Generation with Icon or Digital Micpod


Link Cable – 9M – Phone 2nd Generation with Icon or Digital Micpod


$58.8


This 30-foot Link cable can be used to connect Phones and 2nd Generation Phones to Icon series codecs or expansion MicPods. Electronics Everything in this world is related to electronics and its accessories. In aspects of that our products are very compatible and durable with all kinds of device. These products are recognized for its honesty, high efficiency, and comprehensive services and named for its high standard and quality. Our exclusive products are headlined by hundreds of mind blowing innovations and creativity. FeaturesAccessories and Cables

Intel Comparable 1GBS Dual Open SFP Port Pcie X4 Network Interface Card


Intel Comparable 1GBS Dual Open SFP Port Pcie X4 Network Interface Card


$440.09


This is an Intel I350F2 comparable Gigabit Ethernet PCIe x4 network interface card with 2 included SX SFPs that comply with IEEE 802.3 standards. It is based on an Intel 82576 chipset and is compatible with Windows and Unix-like operating systems. Providing 1Gbs of network speed, it fully supports high-end servers and a variety of networking applications. In addition, this card supports high level VLAN filtering. The dual open SFP ports allows users to choose from a range of SFP transceivers to accommodate multi-mode (MMF) and single-mode (SMF) fiber, granting customizable reach. This product includes both half-height and full-height brackets. All of our network interface cards are 100% compliant, and offer a cost effective solution for all of your network upgrade needs. FeaturesIntel Comparable 1GBS Dual Open SFP Port Pcie X4 Network Interface CardSpecificationsAdditional Information: With 2 1000Base-SX SFP transceiversBus Type: PCIEBus Width: PCIEx4Chipset: Intel 82576Compatible OEM: IntelCompatible OS: Windows Server 2012, Windows 7 (32 and 64 bit), Windows Server 2008 R2, Windows Small Business Server 2007, Windows Server 2008 Final (32 and 64 bit), Windows Server 2003 Final (32 and 64 bit), Windows 8 (32 and 64 bit), Linux Kernel 2.4. x, 2.6. x, and 3. x, FreeBSD 7. x or greater, Windows Vista Final (32 and 64 bit), Windows XP (and Pro) (32 and 64 bit), Netware 6.5Compatible With OEM Part Number: I350F2Data Protocol: EthernetData Rate: 1GbsExternal Connector: SFPMedia Type: MMFNumber of Ports: 2 PortsReach: 550mUNSPSC Code: 43201411Whats In The Box: 1x network interface card, 2x transceiverWeight: 0.5 lbs

Mummy Case For Iphone 4 4S - Neon Blue


Mummy Case For Iphone 4 4S – Neon Blue


$27.11


Balancing expression and functionality, the Mummy case for the iPhone 4 4S reveals just enough to preserve your hardware identity while providing secure storage for a piece of your most essential plastic.Plastic card storageFull access to all switches, ports, cameraImpact resistance protectionSlender, lightweight designSmooth finish repels lintEasy-to-grip textureDimension – 6.5 x 1.13 x 3.5 InItem weight – 0.11 lbColor – Neon Blue.

1GBS Dell Compat Quad RJ45 PCIE X4


1GBS Dell Compat Quad RJ45 PCIE X4


$261


This is a Dell 430-4432 comparable Gigabit Ethernet PCIe 2.0 x4 network interface card with quad RJ-45 ports that comply with IEEE 802.3 standards. It is based on an Intel 82580 chipset and is compatible with a variety of different applications and operating systems, including Windows, Linux and Unix-like systems. Providing 10/100/1000Mbs of network speed, it fully supports high-end servers and various other networking applications. In addition, this card supports high level VLAN filtering. The quad RJ-45 ports operate over copper patch cable, allowing for an operating distance of 100m. This product includes both half-height and full-height brackets. Features1GBS Dell Compat Quad RJ45 PCIE X4SpecificationsBus Type: PCIe 2.0Bus Width: PCIEx4Chipset: Intel 82580Compatible OEM: DellCompatible OS: Windows Server 2012, Windows 7 (32 and 64 bit), Windows Server 2008 R2, Windows Small Business Server 2009, Windows 8.1 (32 and 64 bit), Windows Server 2008 Final (32 and 64 bit), Windows Server 2003 Final (32 and 64 bit), Windows 8 (32 and 64 bit), Windows Server 2012 R2 (64 bit), Linux Kernel 2.4.x, 2.6.x, and 3.x, FreeBSD 7.x or greater, Windows Vista Final (32 and 64 bit), Windows XP (and Pro) (32 and 64 bit)Data Protocol: EthernetData Rate: 10/100/1000MbsExternal Connector: RJ-45Media Type: CopperNumber of Ports: 4 PortsReach: 100mType: Network Interface CardWeight: 0.5 lbs

dbx ZonePRO 641 m Speaker Processor


dbx ZonePRO 641 m Speaker Processor


$439.96


The ZonePRO 641m offers fixed IO, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 641m features a total of six inputs and four outputs. Inputs include four balanced micline switchable terminal block inputs and two mono-summed pairs of unbalanced RCA inputs. Hardware-controlled microphone gain allows adjustment of microphone gain per channel.The 641m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 641m features a power status LED, a network traffic LED, and an RS-232 control port.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable see table for further information. ZonePRO Designer-the configuration, control and monitoring software for the ZonePRO family of devices-offers control of the ZonePRO 641m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-by-step configuration process of the 641m.6 Inputs 4 Outputs4 Balanced MicLine Inputs2 Unbalanced, Mono-Summed RCA Input PairsMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

Dbx Zonepro 641 M Speaker Processor


Dbx Zonepro 641 M Speaker Processor


$499.95


The ZonePRO 641m offers fixed I/O, pre-configured architecture, configurable insert processing and optional duplication of audio channels to another ZonePRO device via a link bus.The 641m features a total of six inputs and four outputs. Inputs include four balanced mic/line switchable terminal block inputs and two mono-summed pairs of unbalanced RCA inputs. Hardware-controlled microphone gain allows adjustment of microphone gain per channel.The 641m device has a pre-configured architecture with input processing, a central matrix and output processing. Two input insert positions and one output insert position allow channel-specific insert processing to be configured. AutoWarmth, a psychoacoustic function that maintains full frequency bandwidth even when the signal level has dropped, is permanently available on each output zone.A link bus allows duplication of the first six audio channels to another ZonePRO device in applications where additional output zones are required.The front panel of the 641m features a power status LED, a network traffic LED, and an RS-232 control port.Additional system control is offered in the form of optional Zone Controllers. This collection of hardware wall-controllers represents a series of simple, elegant user interfaces for functions such as volume, source and preset control.All ZonePRO devices can be controlled by third party control systems via RS-232 or Ethernet as applicable (see table for further information). ZonePRO Designer-the configuration, control and monitoring software for the ZonePRO family of devices-offers control of the ZonePRO 641m via Ethernet or RS-232. The Configuration Wizard within ZonePRO Designer guides users through the step-by-step configuration process of the 641m.6 Inputs / 4 Outputs4 Balanced Mic/Line Inputs2 Unbalanced, Mono-Summed RCA Input PairsMicrophone Gain per ChannelPre-Configured ArchitectureTwo Configurable Input Insert PositionsOne Configurable Output Insert PositionAutoWarmth per Output ZoneLink BusOptional ZC ControllersEthernet ControlSerial ControlThird Party ControlWizard-Driven Configuration

Dbx Pb-48 48-Point 1/4 Patchbay


Dbx Pb-48 48-Point 1/4 Patchbay


$109


Patchbays often go unappreciated until their contacts get rusty or you need just a few more connections. The dbx PB-48 48-point Patchbay takes care of both problems with the greatest of ease. This balanced DBX 1/4″ TRS patchbay has 48 easy-to-reach jacks in the front and rear-96 points in all. Each of its 24-card assemblies has 4 jacks and thumbscrews so switching from normalled to non-normalled positions is easy. Pure nickel silver self-cleaning contacts won’t get funky and waste your connections. The patchbay uses one rackspace. You’ll appreciate its dependability and the price!

dbx PB-48 48-Point 1/4 Patchbay


dbx PB-48 48-Point 1/4 Patchbay


$109


Patchbays often go unappreciated until their contacts get rusty or you need just a few more connections. The dbx PB-48 48-point Patchbay takes care of both problems with the greatest of ease. This balanced DBX 14 TRS patchbay has 48 easy-to-reach jacks in the front and rear-96 points in all. Each of its 24-card assemblies has 4 jacks and thumbscrews so switching from normalled to non-normalled positions is easy. Pure nickel silver self-cleaning contacts wont get funky and waste your connections. The patchbay uses one rackspace. Youll appreciate its dependability and the price

dbx 2231 Dual 31-Band Graphic Equalizer


dbx 2231 Dual 31-Band Graphic Equalizer


$466.36


2231 Dual 31 Band Graphic Equalizer Its amazing. One little button. It has so much effect. The Type III Noise Reduction is an entirely new concept… virtually instantaneous encodedecode within the circuitry of the box. dbx started out to build the finest EQs possible, boxes with the heritage and performance to rival the famous 30 Series EQs. And to no ones surprise they came out awfully darn good. Then came the crazy idea of putting this new noise reduction stuff in the box. Listen and be amazed. The EQs sound great without it, but with it the performance was nothing short of incredible. Check it out yourself and see.Dual-channel 31-bands 13-octave per band PeakPlus limiter LED bar graph for gain reduction and output level Status LEDs for all settings on the front panel XLR, barrier strip, and 14 connectors 45mm nylon sliders 12dB input gain stage

dbx iEQ-31 Graphic EQ


dbx iEQ-31 Graphic EQ


$554.36


dbx IEQ31 Dual 31 Band Graphic EQLimiter Visionary Design Besides including two 31-band channels of 13-octave equalization, the iEQ-31also offers 12 dB input gain range switchable 6 or 15 dB boostcut range,40mm faders, XLR, 14 and Euroblock inputs and outputs, nonconductivenylon sliders and an intuitive user interface with comprehensive output andgain reduction metering. As always, the inevitable result of our meticulousattention to detail and top-quality componentry is exceptional sound, performance,and reliability.Revolutionary Engineering The iEQ series represents a major step forward in the performance of graphicequalizers. The iEQ series is now able to offer state-of-the-art digital EQ performanceand specs with an analog look and feel. From its amazing 10Hz to22kHz frequency response, to its 113dB dynamic range and Advanced FeedbackSuppression AFS, dbx proprietary Type V noise reduction andPeakStopPlus limiting, the iEQ-31 offers out of this world specifications with adown-to-earth price point. Sure to find a home in the studio, on tour and withinstalled sound venues, the iEQ-31 is destined to take its rightful place in thelineage of great dbx signal processors that are the professionals choice in signalprocessing. With such pristine design and quality, the iEQ-31 offers the maximumsonic flexibility in a straight forward interface and rock-solid construction.Dual 15-band EQ AFS one-touch feedback suppression Type V noise reduction PeakStopPlus limiting Switchable 6 or 15dB boostcut range 12dB input gain range 40mm faders Nonconductive nylon sliders 10Hz to 22kHz frequency response 110dB dynamic range 13-octave Constant Q frequency bands Internal toroidal transformer 14 TRS, XLR, and Euroblock balanced and unbalanced RF-filtered inputs and outputs

Radio Replacement for GM 29-Bit Vehicle


Radio Replacement for GM 29-Bit Vehicle


$49.62


Everything in this world is related to electronics and its accessories. In aspects of that our products are very compatible and durable with all kinds of device. These products are recognized for its honesty, high efficiency, and comprehensive services and named for its high standard and quality. Our exclusive products are headlined by hundreds of mind blowing innovations and creativity. FeaturesAftermarket Car Stereo Installation InterfaceFor Select General Motors Lan 29-Bit Vehicles (With Chime, Without Onstar)Safety And Warning ChimesRadio Replacement for GM 29-Bit VehicleSpecificationsVehicle Compability Not Compatible With 2012-Up Suvs/Trucks That Are Equipped With Factory-Installed Navigation Radios. Not Compatble With Diesel-Powered Express And Savana Vans. Does Not Support OnstarDimension: 8.5" H x 1.5" W x 5.5" L

AC250 Camcorder & Digital Camera Case


AC250 Camcorder & Digital Camera Case


$33.93


FeaturesFront pocket provides access to batteries, media cards and accessoriesLarge back pocket holds variety of additional itemsPadded construction is water-resistant for use in most environmentsSpecificationsColor: BlackHi-Vis YellowExterior Material: NylonDimension: 7.3 x 7.1 x 4.1 in.

Radio Replacement with SWC Retention for GM LAN 29 Bit Vehicles


Radio Replacement with SWC Retention for GM LAN 29 Bit Vehicles


$90.31


FeaturesGM LAN 29 Bit vehicles while functioning with an aftermarket radioPre-programmed to retain factory steering wheel controlsSWC on select kenwood, pioneer, alpine and JVC radiosSupports Bose, non-Bose and Y-91 audio systemsSpecificationsDimension: 8.5" H x 3.5" W x 5" LWeight: 0.6 lbs

Onstar Radio Replace Interface for GM LAN 29-Bit with SWC and Video Switcher


Onstar Radio Replace Interface for GM LAN 29-Bit with SWC and Video Switcher


$125.94


Designed to allow for the installation of after-market radios while retaining functionality of OnStar in Bose Amplified and Non-Amplified Systems, Chime and Accessory features in General Motors LAN 29-Bit vehicles. Also retains steering wheel controls and adds camera switching capability for forced front-view & rear-view cameras.FeaturesRetains factory features in select GM LAN 29 Bit vehicles while functioning with an aftermarket radio.Pre-programmed to retain factory Steering Wheel Controls.Retains OnStar, factory Rear view camera and chime functions.Adds Forced Rear view and Front view camera while in motion using the factory side mirror controls.Supports Bose, non-Bose and Y-91 audio systems.EIA color coded wiring for easy installation

Select 2 Farad Power Capacitor with Digital Display


Select 2 Farad Power Capacitor with Digital Display


$41.57


Select 2 Farad Power Capacitor with Digital Display Select Capacitors provide instantaneous power on demand to feed power hungry amplifiers. When system voltages drop, sound quality and output power suffers. SS capacitors stabilize this voltage so your system performs at it's peak. The integrated digital display informs you of system status and performance. Good for systems up to 2000 watts. FeaturesDigital displayBrushed Aluminum BodySatin Finish TerminalsUP to 2000W2 FaradSpecificationsDimension: 10" H x 3.75" W x 13.5" LWeight: 3.55 lbs

Link Cable - 4M - Phone 2nd Generation with Icon or Digital Micpod


Link Cable – 4M – Phone 2nd Generation with Icon or Digital Micpod


$67.43


Electronics Everything in this world is related to electronics and its accessories. In aspects of that our products are very compatible and durable with all kinds of device. These products are recognized for its honesty, high efficiency, and comprehensive services and named for its high standard and quality. Our exclusive products are headlined by hundreds of mind blowing innovations and creativity. FeaturesLink Cable - 4M - Phone 2nd Generation with Icon or Digital Micpod

Link Cable - 15 m Phone, 2Nd Generation with Icon Or Digital Micpod


Link Cable – 15 m Phone, 2Nd Generation with Icon Or Digital Micpod


$122.06


If you are a gadget lover, our Electronics catalog is your dream destination. Choose from hundreds of gadgets and accessories to suit different uses and add some entertainment, facility and convenience to your life.FeaturesLots of options in every categoryHigh quality construction and modern designsSuperior quality performance and reliabilityCompetitive prices and value for moneyFeatures Link Cable - 15M Phone, 2Nd Generation with Icon Or Digital MicpodSpecificationsWeight : 1.000 lbs

Mummy Case For Iphone 5 - White


Mummy Case For Iphone 5 – White


$27.11


Balancing expression and functionality, the Mummy case for the iPhone 5 reveals just enough to preserve your hardware identity while providing secure storage for a piece of your most essential plastic.Plastic card storageFull access to all switches, ports, cameraImpact resistance protectionSlender, lightweight designSmooth finish repels lintEasy-to-grip textureDimension – 7.56 x 0.63 x 3.56 InItem weight – 0.13 lbColor – White.

24 ft. Watchman Clear Lens Liner LED


24 ft. Watchman Clear Lens Liner LED


$349.3


FeaturesHigh intensity linear LED clustersWider light beam of light is the new optical lens that has a unique inner magnifierCommand center of the light bar for all functionsUltra bright beam of light that will be seen 360 degrees even in bright daylightInvisible when mounted on the vehicle s roofSpecificationsColor: ClearSize: 24'Material: Adjustable ABS base bracket and stainless-steel strapsVolt: 12VDimension: 4.25" H x 11.8" W x 46.75" L

1 corinthians 1 9 challenging church


1 corinthians 1 9 challenging church


$2


Very Good pp. 96. No markings.

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 30,000 BTU 96% Efficiency Gas Furnace Horizontal System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 30,000 BTU 96% Efficiency Gas Furnace Horizontal System by Heat and Cool


$2263.96


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CHPF3636B6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CHPF3636B6 Horizontal Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Painted cased coil for horizontal ‘A’ applications. Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils on the CAPF, CAUF, and CHPF coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on coils Split-seam front for easy access Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines AHRI certified ETL listed DC-GMEC960302BN & verbar- Gas Furnace The DC-GMEC960302BN 96&percnt- high efficiency furnace from Goodman’s Direct Comfort saves you money from the moment it arrives. Its versatile design makes installation easy and fast. Once it’s running, you’ll notice a reduction in your energy bill since 96 cents of every dollar you spend on heating will actually go toward warming your home. Unlike a standard furnace, which vents leftover heat out of your home in the form of exhaust, the Goodman 96&percnt- AFUE DC-GMEC960302BN multi-speed furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That heat – up to 30&percnt- or more – which would have otherwise been wasted is circulated through your home by a dual-speed induced draft blower. Additionally, the multi-speed ECM motor also keeps your home temperature steady and several low continuous fan speed options reduce sound and keeps air circulating throughout your home. The self-diagnostic control board with fault code history helps maintain your investment for long-lasting comfort. Ideal for installation in a closet, alcove, utility room, basement or attic. Additional Features: Energy-efficiency optimized by 2-stage gas valve and 2-speed induced draft blower Heavy-gauge steel cabinet with durable finish Fully insulated heat exchanger and blower section Durable silicon nitride igniter Certified for direct vent & lpar-2-pipe & rpar- or non-direct vent & lpar-1-pipe & rpar- Complies with California 40 ng & sol-J Low NOx emissions standard Self-diagnostic control board with constant memory fault code history output to a dual 7-segment display Designed for multi-position installation – upflow, horizontal left or right Easy-to-install top venting with optional side venting and left or right connection for gas a

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 30,000 BTU 96% Efficiency Gas Furnace Upflow System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 30,000 BTU 96% Efficiency Gas Furnace Upflow System by Heat and Cool


$2314.95


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CAPF3636C6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CAPF3636C6 Upflow & sol-Downflow Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Cased coil for upflow & sol-downflow applications. Additional Features Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on cased coils Split-seam front for easy access AHRI certified ETL listed DC-GMEC960302BN & verbar- Gas Furnace The DC-GMEC960302BN 96&percnt- high efficiency furnace from Goodman’s Direct Comfort saves you money from the moment it arrives. Its versatile design makes installation easy and fast. Once it’s running, you’ll notice a reduction in your energy bill since 96 cents of every dollar you spend on heating will actually go toward warming your home. Unlike a standard furnace, which vents leftover heat out of your home in the form of exhaust, the Goodman 96&percnt- AFUE DC-GMEC960302BN multi-speed furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That heat – up to 30&percnt- or more – which would have otherwise been wasted is circulated through your home by a dual-speed induced draft blower. Additionally, the multi-speed ECM motor also keeps your home temperature steady and several low continuous fan speed options reduce sound and keeps air circulating throughout your home. The self-diagnostic control board with fault code history helps maintain your investment for long-lasting comfort. Ideal for installation in a closet, alcove, utility room, basement or attic. Additional Features: Energy-efficiency optimized by 2-stage gas valve and 2-speed induced draft blower Heavy-gauge steel cabinet with durable finish Fully insulated heat exchanger and blower section Durable silicon nitride igniter Certified for direct vent & lpar-2-pipe & rpar- or non-direct vent & lpar-1-pipe & rpar- Complies with California 40 ng & sol-J Low NOx emissions standard Self-diagnostic control board with constant memory fault code history output to a dual 7-segment display Designed for multi-position installation – upflow, horizontal left or right Easy-to-install top venting with optional side venting and left or right connection for gas and

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 30,000 BTU 96% Efficiency Gas Furnace Upflow System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 30,000 BTU 96% Efficiency Gas Furnace Upflow System by Heat and Cool


$2299.08


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CAPF3636B6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CAPF3636B6 Upflow & sol-Downflow Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Cased coil for upflow & sol-downflow applications. Additional Features Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on cased coils Split-seam front for easy access AHRI certified ETL listed DC-GMEC960302BN & verbar- Gas Furnace The DC-GMEC960302BN 96&percnt- high efficiency furnace from Goodman’s Direct Comfort saves you money from the moment it arrives. Its versatile design makes installation easy and fast. Once it’s running, you’ll notice a reduction in your energy bill since 96 cents of every dollar you spend on heating will actually go toward warming your home. Unlike a standard furnace, which vents leftover heat out of your home in the form of exhaust, the Goodman 96&percnt- AFUE DC-GMEC960302BN multi-speed furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That heat – up to 30&percnt- or more – which would have otherwise been wasted is circulated through your home by a dual-speed induced draft blower. Additionally, the multi-speed ECM motor also keeps your home temperature steady and several low continuous fan speed options reduce sound and keeps air circulating throughout your home. The self-diagnostic control board with fault code history helps maintain your investment for long-lasting comfort. Ideal for installation in a closet, alcove, utility room, basement or attic. Additional Features: Energy-efficiency optimized by 2-stage gas valve and 2-speed induced draft blower Heavy-gauge steel cabinet with durable finish Fully insulated heat exchanger and blower section Durable silicon nitride igniter Certified for direct vent & lpar-2-pipe & rpar- or non-direct vent & lpar-1-pipe & rpar- Complies with California 40 ng & sol-J Low NOx emissions standard Self-diagnostic control board with constant memory fault code history output to a dual 7-segment display Designed for multi-position installation – upflow, horizontal left or right Easy-to-install top venting with optional side venting and left or right connection for gas and

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Downflow System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Downflow System by Heat and Cool


$2762.94


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CAPF3636C6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CAPF3636C6 Upflow & sol-Downflow Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Cased coil for upflow & sol-downflow applications. Additional Features Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on cased coils Split-seam front for easy access AHRI certified ETL listed DC-GCVC960403BN & verbar- Gas Furnace When you choose a Goodman’s Direct Comfort high efficiency gas furnace system you’re not the only one who benefits. High efficiency means you’ll lower your operating cost – great for you & excl- And you’ll reduce your environmental footprint – great for the global community. Then, of course, anyone who spends time in your house will enjoy balanced room comfort and better indoor air quality. Invest in Goodman and share the comfort. This 96&percnt- high efficiency 40,000 BTU 2-stage condensing furnace by Goodman, model DC-GCVC960403BN, has been carefully engineered to work to its fullest capacity. When it comes to your personal comfort, no detail has been overlooked. The furnace’s variable speed ECM blower gently ramps up or down according to heating demands keeping sound at a minimum and energy costs low. The multiple continuous fan speed options quietly circulate the air keeping the temperature balanced and steady. Unlike a standard furnace, which vents left-over heat out of your home in the form of exhaust, the Goodman high-efficient furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That extra heat – up to 30&percnt- more – which would have otherwise been wasted is circulated through your home by a near-silent two-speed induced draft blower. The end result is 96 cents out of every dollar you spend on heating is used to keep your home warm. The two-stage gas valve works in unison with the variable speed motor to save energy and maintain an even indoor temperature by adjusting its airflow according to the heating demands of your home. Also enjoy advanced diagnostics, automatic maintenance alerts and continuous monitoring of the system’s performance. Ideal for installation in a closet, alcove, utility room, basement or attic. Additional Features Compatible with

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Downflow System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Downflow System by Heat and Cool


$2747


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CAPF3636B6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CAPF3636B6 Upflow & sol-Downflow Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Cased coil for upflow & sol-downflow applications. Additional Features Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on cased coils Split-seam front for easy access AHRI certified ETL listed DC-GCVC960403BN & verbar- Gas Furnace When you choose a Goodman’s Direct Comfort high efficiency gas furnace system you’re not the only one who benefits. High efficiency means you’ll lower your operating cost – great for you & excl- And you’ll reduce your environmental footprint – great for the global community. Then, of course, anyone who spends time in your house will enjoy balanced room comfort and better indoor air quality. Invest in Goodman and share the comfort. This 96&percnt- high efficiency 40,000 BTU 2-stage condensing furnace by Goodman, model DC-GCVC960403BN, has been carefully engineered to work to its fullest capacity. When it comes to your personal comfort, no detail has been overlooked. The furnace’s variable speed ECM blower gently ramps up or down according to heating demands keeping sound at a minimum and energy costs low. The multiple continuous fan speed options quietly circulate the air keeping the temperature balanced and steady. Unlike a standard furnace, which vents left-over heat out of your home in the form of exhaust, the Goodman high-efficient furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That extra heat – up to 30&percnt- more – which would have otherwise been wasted is circulated through your home by a near-silent two-speed induced draft blower. The end result is 96 cents out of every dollar you spend on heating is used to keep your home warm. The two-stage gas valve works in unison with the variable speed motor to save energy and maintain an even indoor temperature by adjusting its airflow according to the heating demands of your home. Also enjoy advanced diagnostics, automatic maintenance alerts and continuous monitoring of the system’s performance. Ideal for installation in a closet, alcove, utility room, basement or attic. Additional Features Compatible with

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Horizontal System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Horizontal System by Heat and Cool


$2306.93


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CHPF3636B6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CHPF3636B6 Horizontal Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Painted cased coil for horizontal ‘A’ applications. Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils on the CAPF, CAUF, and CHPF coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on coils Split-seam front for easy access Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines AHRI certified ETL listed DC-GMEC960402BN & verbar- Gas Furnace The DC-GMEC960402BN 96&percnt- high efficiency furnace from Goodman’s Direct Comfort saves you money from the moment it arrives. Its versatile design makes installation easy and fast. Once it’s running, you’ll notice a reduction in your energy bill since 96 cents of every dollar you spend on heating will actually go toward warming your home. Unlike a standard furnace, which vents leftover heat out of your home in the form of exhaust, the Goodman 96&percnt- AFUE DC-GMEC960402BN multi-speed furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That heat – up to 30&percnt- or more – which would have otherwise been wasted is circulated through your home by a dual-speed induced draft blower. Additionally, the multi-speed ECM motor also keeps your home temperature steady and several low continuous fan speed options reduce sound and keeps air circulating throughout your home. The self-diagnostic control board with fault code history helps maintain your investment for long-lasting comfort. Ideal for installation in a closet, alcove, utility room, basement or attic. Additional Features: Energy-efficiency optimized by 2-stage gas valve and 2-speed induced draft blower Heavy-gauge steel cabinet with durable finish Fully insulated heat exchanger and blower section Durable silicon nitride igniter Certified for direct vent & lpar-2-pipe & rpar- or non-direct vent & lpar-1-pipe & rpar- Complies with California 40 ng & sol-J Low NOx emissions standard Self-diagnostic control board with constant memory fault code history output to a dual 7-segment display Designed for multi-position installation – upflow, horizontal left or right Easy-to-install top venting with optional side venting and left or right connection for gas a

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Horizontal System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Horizontal System by Heat and Cool


$2712.13


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CHPF3636B6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CHPF3636B6 Horizontal Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Painted cased coil for horizontal ‘A’ applications. Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils on the CAPF, CAUF, and CHPF coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on coils Split-seam front for easy access Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines AHRI certified ETL listed DC-GCVC960403BN & verbar- Gas Furnace When you choose a Goodman’s Direct Comfort high efficiency gas furnace system you’re not the only one who benefits. High efficiency means you’ll lower your operating cost – great for you & excl- And you’ll reduce your environmental footprint – great for the global community. Then, of course, anyone who spends time in your house will enjoy balanced room comfort and better indoor air quality. Invest in Goodman and share the comfort. This 96&percnt- high efficiency 40,000 BTU 2-stage condensing furnace by Goodman, model DC-GCVC960403BN, has been carefully engineered to work to its fullest capacity. When it comes to your personal comfort, no detail has been overlooked. The furnace’s variable speed ECM blower gently ramps up or down according to heating demands keeping sound at a minimum and energy costs low. The multiple continuous fan speed options quietly circulate the air keeping the temperature balanced and steady. Unlike a standard furnace, which vents left-over heat out of your home in the form of exhaust, the Goodman high-efficient furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That extra heat – up to 30&percnt- more – which would have otherwise been wasted is circulated through your home by a near-silent two-speed induced draft blower. The end result is 96 cents out of every dollar you spend on heating is used to keep your home warm. The two-stage gas valve works in unison with the variable speed motor to save energy and maintain an even indoor temperature by adjusting its airflow according to the heating demands of your home. Also enjoy advanced diagnostics, automatic maintenance alerts and continuous monitoring of the system’s performance. Ideal for installation in a closet, alcove, utility room, basement or attic. Additional Features Compatible wit

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Horizontal System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Horizontal System by Heat and Cool


$2340.07


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CHPF3636B6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CHPF3636B6 Horizontal Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Painted cased coil for horizontal ‘A’ applications. Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils on the CAPF, CAUF, and CHPF coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on coils Split-seam front for easy access Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines AHRI certified ETL listed DC-GMVC960403BN & verbar- Gas Furnace When you choose a Goodman’s Direct Comfort high efficiency gas furnace system you’re not the only one who benefits. High efficiency means you’ll lower your operating cost – great for you & excl- And you’ll reduce your environmental footprint – great for the global community. Then, of course, anyone who spends time in your house will enjoy balanced room comfort and better indoor air quality. Invest in Goodman and share the comfort. This 80&percnt- high efficiency 40000 BTU 2-stage condensing furnace by Goodman Direct Comfort, model DC-GMVC960403BN has been carefully engineered to work to its fullest capacity. When it comes to your personal comfort, no detail has been overlooked. The furnace’s variable speed ECM blower gently ramps up or down according to heating demands keeping sound at a minimum and energy costs low. The multiple continuous fan speed options quietly circulate the air keeping the temperature balanced and steady. Unlike a standard furnace, which vents left-over heat out of your home in the form of exhaust, the Goodman’s Direct Comfort high-efficient furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That extra heat – up to 30&percnt- more – which would have otherwise been wasted is circulated through your home by a near-silent two-speed induced draft blower. The end result is 96 cents out of every dollar you spend on heating is used to keep your home warm. The two-stage gas valve works in unison with the variable speed motor to save energy and maintain an even indoor temperature by adjusting its airflow according to the heating demands of your home. Also enjoy advanced diagnostics, automatic maintenance alerts and continuous monitoring of the system’s performance. Ideal for installation in a closet, alcove, utility room, basement or attic. Additiona

1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Upflow System by Heat and Cool


1.5 Ton A/C Direct Comfort 14 SEER Central Air Conditioner 40,000 BTU 96% Efficiency Gas Furnace Upflow System by Heat and Cool


$2358.04


Direct Comfort, by Goodman Complete Heating and Cooling for Year-Round Comfort and Energy Savings The DC-GSX140181, 1.5 Ton, central air conditioning system will help reduce energy consumption throughout the life of the system. Goodman’s Direct Comfort SMARTCOIL™ 5mm tube condensing coil design optimizes the heat transfer ability of R-410A refrigerant compared to standard 3&sol-8″copper tubing. The coil is made of rifled refrigeration-grade copper tubing and corrugated aluminum fins in a design that maximizes surface area. These high-quality components together cool your home effectively. DC-GSX140181 & verbar- Outdoor Condensing UnitThe Goodman’s Direct Comfort DC-GSX140181 uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the DC-GSX140181 will help reduce energy consumption throughout the life of the system. Standard Features: Energy-efficient compressor Factory-installed filter drier Copper tube & sol-aluminum fin coil Service valves with sweat connections and easy-access gauge ports Contactor with lug connection Ground lug connection AHRI Certified ETL Listed Cabinet Features: Goodman’s Direct Comfort louvered sound control top design Steel louver coil guard Heavy-gauge galvanized-steel cabinet Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval Top and side maintenance access Single-panel access to controls with space provided for field installed accessories When properly anchored, meets the 2010 Florida Building Code unit integrity requirements for hurricane-type winds Anchor bracket kits available DC-CAPF3636C6 & verbar- Indoor Unit Coil Component The Goodman’s Direct Comfort DC-CAPF3636C6 Upflow & sol-Downflow Cased Indoor Air Conditioner Evaporator Coil is made for use with split-system air conditioning and Evaporator systems. The all-aluminum evaporator coil is constructed from aluminum tubing, corrugated fins and panels giving you a single metal solution for outstanding, time-tested, heat transfer performance properties. Cased coil for upflow & sol-downflow applications. Additional Features Helium pressure-tested during construction Finished pressure tested and vacuum tested with leak “sniffing” by “hound-dog” Aluminum-lanced sine fin design for optimum heat transfer Thick-walled aluminum tubing provides superb strength Copper coil stud for connecting copper liquid suction lines Suitable for use with R-410A and R-22 refrigerants Rust-resistant, thermoplastic drain pans feature a low water-retention design Check flowrater expansion device for heat pump or cooling-only applications Rifled aluminum tubing and louvered aluminum fin coils Foil-face insulation Galvanized-steel, leather-grain finish Architectural Gray paint finish on cased coils Split-seam front for easy access AHRI certified ETL listed DC-GMEC960402BN & verbar- Gas Furnace The DC-GMEC960402BN 96&percnt- high efficiency furnace from Goodman’s Direct Comfort saves you money from the moment it arrives. Its versatile design makes installation easy and fast. Once it’s running, you’ll notice a reduction in your energy bill since 96 cents of every dollar you spend on heating will actually go toward warming your home. Unlike a standard furnace, which vents leftover heat out of your home in the form of exhaust, the Goodman 96&percnt- AFUE DC-GMEC960402BN multi-speed furnace passes the exhaust through a secondary stainless steel heat exchanger to extract additional heat. That heat – up to 30&percnt- or more – which would have otherwise been wasted is circulated through your home by a dual-speed induced draft blower. Additionally, the multi-speed ECM motor also keeps your home temperature steady and several low continuous fan speed options reduce sound and keeps air circulating throughout your home. The self-diagnostic control board with fault code history helps maintain your investment for long-lasting comfort. Ideal for installation in a closet, alcove, utility room, basement or attic. Additional Features: Energy-efficiency optimized by 2-stage gas valve and 2-speed induced draft blower Heavy-gauge steel cabinet with durable finish Fully insulated heat exchanger and blower section Durable silicon nitride igniter Certified for direct vent & lpar-2-pipe & rpar- or non-direct vent & lpar-1-pipe & rpar- Complies with California 40 ng & sol-J Low NOx emissions standard Self-diagnostic control board with constant memory fault code history output to a dual 7-segment display Designed for multi-position installation – upflow, horizontal left or right Easy-to-install top venting with optional side venting and left or right connection for gas and
Advertisement

Comments are closed.